No matter what device you may think of, all machines derive from six basic simple foundations. From these foundations, we have built many more complicated fixtures which perform different functions.

However, those fundamental machines at the bottom of the evolutionary creation process remain the same. At the most basic level, work is performed by applying a force over a distance.

These simple machines create a greater output force than Levitra the input force; the ratio of these forces is the mechanical advantage of the machine. All six of the simple mechanics have been used for thousands of years, and the physics behind several of them were quantified by Archimedes-these can even be used together to create even greater mechanical advantage, as in the case of a bicycle.

To begin there is the lever. A lever is a simple machine that consists of a rigid object, often a bar of some kind, and a fulcrum or pivot.

Applying a force to one end of the rigid object causes it to pivot about the fulcrum, causing a magnification of the force at another point along the rigid object. There are three classes of levers, depending on where the input force, output force, and fulcrum are in relation to each other.

Baseball bats, seesaws, wheelbarrows, and crowbars are types of levers. We use these simple lever mechanics every day, though we may not even realize it.

The next is the wheel and axle. A wheel is a circular device that is attached to a rigid bar in its center.

A force applied to the wheel causes the axle to rotate, which can be used to magnify the force by, for example, having a rope wind around the axle. Alternately, a force applied to provide rotation on the axle translates into rotation of the wheel.

It can be viewed as a type of lever that rotates around a center fulcrum. Ferris wheels, tires, and rolling pins are examples of wheels and axles.

Without wheels we wouldn’t have bikes, cars, trains, planes, or a number of other modern conveniences and necessities. The axle and wheel has revolutionized our very world.

The next machine is an inclined plane. An inclined plane is a plane surface set at an angle to another surface.

This results in doing the same amount of work by applying the force over a longer distance. The most basic inclined plane is a ramp; it requires less force to move up a ramp to a higher elevation than to climb to that height vertically.

The wedge is often considered a specific type of inclined plane. Without wedges we would not have the stability which makes many other devices and even building concepts possible.

A wedge is a double-inclined plane, both sides are inclined, that moves to exert a force along the lengths of the sides. The force is perpendicular to the inclined surfaces, so it pushes two objects, or portions of a single object, apart.

Axes, knives, and chisels are all wedges. The common “door wedge” uses the force on the surfaces to provide friction, rather than separate things, but it’s still fundamentally a wedge.

Next, we have the screw, an incredibly important step to making almost all modern machines. A screw is a shaft that has an inclined groove along its surface.

By rotating the screw or applying a torque, the force is applied perpendicular to the groove, thus translating a rotational force into a linear one. It is frequently used to fasten objects together, as the hardware screw and bolt does, although Babylonians developed a “screw” that could elevate water from a low-lying body to a higher one, a concept which later came to be known as Archimedes’ screw.

Last but not least we have the pulley. A pulley is a wheel with a groove along its edge, where a rope or cable can be placed.

It uses the principle of applying force over a longer distance, and also the tension in the rope or cable, to reduce the magnitude of the necessary force. Complex systems of pulleys can be used to greatly reduce the force that must be applied initially to move an object.

As you can see, these six basic machines have been the foundation of all other more complex machines which we have dreamed to devise. Look for them, and you are sure to find them everywhere-even where you least expect it.

Author Bio: Jack R. Landry has used metalworking equipment for the last 11 years and written hundreds of articles about machinery and Durma machinery and tools.

Contact Info:

Jack R. Landry

JackRLandry@gmail.com

http://www.jorgensonmachinetools.com

Category: Business/Medium Sized
Keywords: Durma