TILE & GROUT CAULKING BASICS

Every caulking job has different requirements and variables. Proper application starts with knowing the right type of caulk to use and a plan to complete the particular job.

The interior areas of the house which are most prone to water damage are the kitchen and bath. Because of constant moisture in these areas, we must be alert to the maintenance needs of caulking, sealing and protecting our home from water intrusion into the wood members which can cause rot and deterioration.

Caulking tile and grout areas that have been cracked, crumbling and in need of repair, should start with a basic knowledge of preparation and application.

Preparing the tiled area to be sealed with caulk always includes removal of debris and thorough cleaning. Filling the gap with caulk without cleaning, will not ensure the caulk will even adhere to the surface your trying to repair. To achieve the best longevity for the time, effort and money you spend on your project, make sure you scrape, brush and blow out loose particles and dirt in and around the gap.

If you have never used a caulking gun, practice a couple beads on an area first to get the hang of it. Buy a caulking gun that is a \”drip-less model\”. That means the caulk gun automatically releases pressure on the tube when you release the trigger so that caulk does not run out of the tube constantly. You can control the flow much better this way.

Cut the tip of the caulk tube at about a 30 degree angle. For a small tile or grout joint, cut the tip narrow and for larger gaps, cut more of the tip. Insert the tube into the caulking gun and as you squeeze the trigger, always pull the caulk along the joint. Making contact with the surface of the joint will ensure a smoother application. This will help force the caulk into making good contact in the joint.

TOOLING THE CAULK- Tile and Grout Acrylic Latex

Tile & Grout siliconized acrylic latex caulk comes in hundreds of grout colors, and you will find it one of the easiest caulk to tool smooth. You can purchase either sanded or smooth tile and grout caulk. As with most caulk, never overfill the joints you are caulking. Try to just fill the caulk to the top of the joint and pull along your path. With latex caulk, you can caulk all three sides of a tub at once without tooling them independently. Latex caulk gives you plenty of time to tool without \”skinning over\” too quickly.

Have a small bucket half filled with water and a sponge. A soft sponge is the best. Use your wet finger to lightly but firmly slide all the way around the tub joint or grout crack you have just filled. Every foot or so, you will probably have to wipe the excess caulk off your finger onto a paper towel. Keep fingering the entire caulk joint until you reach the end. Now with your wet sponge slightly wrung, wipe the caulk joint with a long sweep, then flip the sponge over and continue. Wring the sponge out clean with water and keeping it semi wet, continue on. This will clean the surfaces on either side of the joint and also will help smooth the caulk.

There are tools out there for smoothing latex caulk and some people like using a wet cotton cloth with a spoon or a plastic caulk tool, but I have found the finger method and sponge to be the easiest application for smoothing acrylic latex caulk.

TOOLING THE CAULK- Tile and Grout Ultra-Performance Caulk

Tooling the Ultra-Performance commercial grade caulk requires a little more skill than the acrylic latex caulk. This is a hybrid formulated caulk that cleans up with mineral spirits. It has properties that are water-resistant, long-lasting, very flexible and very resistant to harsh conditions. These attributes make it perfect for outdoor use on sidewalks, expansion joints, wall cracks, swimming pool tile and indoors for showers and baths.

Taping off both edges of the gap you are filling is a nice way to ensure a perfect bead. Once the caulk is laid into the gap, smooth it with your finger or a flat piece of plastic or even a spoon, being careful not to remove so much caulk that it creates a dip in the flow. A little pressure although, is good for the caulk adhesion to the substrate. Keep rags and paper towels handy and a can of mineral spirits for cleaning. The Ultra-Performance will start to skin over in about 10 minutes depending on temperature, so try to not overwork the caulk. Peel the tape off while the caulk is soft so it pulls away cleanly and leaves a nice straight line.

If you do not want to tape off the area to be filled, do not overfill the gap. Pulling too much caulk with your finger tends to pull out too much material. Use a light touch with your finger or tool that is wet with mineral spirits. This will help lubricate the caulk for spreading.

TOOLING THE CAULK – Granite and Marble Silicone Caulk

Silicone caulk is very waterproof and adhesive. With a wide range of uses, it now has many different colors available in solid and translucent colors. It is highly resistant to ultraviolet light, ozone, moisture, mildew and extreme temperature variations. Tooling this silicone caulk is easier now that they have instilled some high-grade additives.

A pro usually can get a perfect bead every time because of his or her experience with silicon application. This includes laying down the right size of bead for the gap. Also, with silicone, it likes one smooth wipe the best. You can tool it 2 or 3 times, but silicone will lay down and blend better the less you tool it.

Using your index finger is a good method, and having it wet with mineral spirits or rubbing alcohol will help smooth it nicely. Do not lay down more bead then the joint requires. Silicone likes to spread out wide and you don\’t want gobs of it in front of your finger as you pull. A light smooth consistent pull will make the joint perfect!

If you are searching for colored caulk or grout colorants to match or change the color of your tile grout, go now to http://www.groutgetter.com. Mike Garman is an expert in home repair and founder of Grout Getter Company. Thousands of people have ordered through this site to repair and seal their cracked or missing grout. Tile and grout caulk and colorants are available in hundreds of colors of all the major brand grout companies.

Michael Garman has 30 years experience as a licensed building contractor and performed work in several of the specialty trades. He also served in California as a certified building inspector for residential homes and is involved in safety recommendations and product installation for the disabled. In 1993 he founded Grout Getter Company, http://www.groutgetter.com where he developed tile tools for professional and homeowners alike. His company added colored caulk and grout colorants to complete the product line.

Michael Garman has 30 years experience as a licensed building contractor and performed work in several of the specialty trades. He also served in California as a certified building inspector for residential homes and is involved in safety recommendations and product installation for the disabled. In 1993 he founded Grout Getter Company, http://www.groutgetter.com where he developed tile tools for professional and homeowners alike. His company added colored caulk and grout colorants to complete the product line.

Author Bio: Michael Garman has 30 years experience as a licensed building contractor and performed work in several of the specialty trades. He also served in California as a certified building inspector for residential homes and is involved in safety recommendations and product installation for the disabled. In 1993 he founded Grout Getter Company, http://www.groutgetter.com where he developed tile tools for professional and homeowners alike. His company added colored caulk and grout colorants to complete the product line.

Category: Home Management
Keywords: color caulk, tile grout, tile caulking, grout colorant, colored grout, grout getter