Tips on How to Fix Toilet Water Tank Problem Effectively:

Are you confusing on how to fix the toilet water tank while it has problem? The following article will help you from A to Z:

To compare with a clogged toilet, water tank troubles can seem relatively insignificant. Yet strange noises or continuous water leaking can be more than annoying. They can also be costing you money in wasting water quickly. Fortunately, you can solve most water tanks\’ troubles quickly and easily by yourself.

Toilet water tank troubles are both common and annoying, and they could be costing you money in wasted water. Most problems, however, can be eliminated quickly and easily. This is a cross section of a typical toilet tank and its components.

Once you know how the toilet water tank works, you can start to look for the source of toilet tank problems. Lift the lid off your toilet water tank, and you should be able to follow this procedure quite easily.

When you trip the handle on the tank to flush a toilet, a trip lever is raised inside the tank. This lever lifts wires, which, in turn, raise the tank ball or rubber flap at the bottom of the tank. When the flush valve opening is clear, the water in the tank rushes out past the raised tank ball and into the toilet bowl below. This raises the level of water in the bowl above the level of water in the toilet trap.

While the water is rushing out of the tank, the float ball, which floats on top of the water in the tank, drops down. This pulls down on the float arm, raising the valve plunger in the ballcock assembly and allowing fresh water to flow into the water tank. Since water seeks its own level, the water from the tank pushes the bowl water out into the drain, causing a siphoning action that cleans everything out of the bowl. When all the water is gone from the toilet bowl and air is drawn into the trap, the siphoning stops. Meanwhile, the tank ball falls back into place, closing the flush valve opening.

Xiamen BQM Sanitary Ware Technology Inc. (Professional toilet water tank fittings designer and manufacturer.)

As the water level rises in the water tank, the float ball rises until the float arm is high enough to lower the valve plunger in the ballcock assembly and shut off the incoming water. If the water fails to shut off there is an overflow tube that carries excess water down into the bowl to prevent the tank from overflowing. If water flows continuously out of the tank to the bowl and down the drain:

Step No.1: Lift up on the float arm. If the water stops, you know the problem is that the float ball doesn’t rise far enough to lower the valve plunger in the ballcock assembly. One reason could be that the float ball is rubbing against the side of the tank. If this is the case, bend the float arm slightly to move the ball away from the tank side.

If your water tank runs continuously, check the guide and lift wire that raises and lowers the tank ball to be sure they are aligned properly.

Step No.2: If the ball doesn’t touch the tank, continue to hold the float arm and remove the ball from the end of the arm by turning it counterclockwise. Then shake the ball to see if there’s water inside it, as the weight of the water inside could be preventing the ball from rising normally. If there is water in the ball, shake it out and put the ball back on the float arm. If the ball is damaged or corroded, replace it with a new one. If there is no water in the ball, put the ball back on and gently bend the float rod down to lower the level the float ball must reach to shut off the flow of fresh water into the tank.

Step NO. 3: If the above steps don’t solve the problem, check the water tank ball at the flush valve seat. Chemical residue from the water can prevent this ball from seating properly, or the ball itself may have decayed. Water will seep through the flush valve opening into the toilet bowl below. Turn off the water at the toilet shutoff valve and flush the toilet to empty the tank. You can now examine the tank ball for signs of wear and examine the tank ball for signs of wear and install a new ball if necessary. If the problem is chemical residue on the lip of the flush valve opening, take some wet-dry emery cloth, steel wool, or even a knife and clean away the debris.

Step NO.4: If the excess water still flows through the toilet water tank, the guide or the lift wire that raises and lowers the water tank ball may be out of the line or bent. Make sure the guide is in place so that the wire is directly above the flush valve opening. Rotate the guide until the tank ball falls straight down into the opening. If a lift wire is bent, try to bend it back to the correct position, or install a new one. Make sure the trip lever rod is not rubbing against anything and the lift wire is not installed in the wrong hole of the rod; either situation could cause the tank ball to fall at an angle and not block the opening as it should.

If neither the float ball not the tank ball is at fault, then the problem must be in the ballcock assembly.

Hope the above article would be helpful for you on solving the problems of your toilet water tank. If any other questions, please feel feel to send email to us. We will reply you with the detailed solution as soon as possible.

Edited by Xiamen BQM Sanitary Ware Technology Inc.

Email: bqmchina@yahoo.com

China BQM is located at the special economic zone & seaport city of Xiamen. We specialize in designing and manufacturing toilet water tank fittings such as fill & flush valve, push button, water-saving devices, and other related products. Thanks to the continuous development and innovation since establishment, we have already become a strong pioneer in the water-saving and energy-saving area.

All of our products are famous for elegant appearance, super quality, energy-saving and eco-friendly design. We are pursuing continuous innovation based on top quality standards. In management, we adopt the workable and reliable theory, such as 6-Sigma, JIT, TQC, and so on. In order to improve our management level, our management team firmly abides by the quality management system of ISO9001:2008 and actively perfects our quality assurance system. Our products have gained the international authority approvals of CSC (China), CUPC (America&Canada), WaterMark (Australia), PSB Test (Singapore), etc., which can be selected to meet most customers’ demands immediately. Besides the top quality assurance, we are very proud of our warm and considerate service as well. Our professional marketing teams always strive to have all-out efforts to satisfy different kinds of requirements from any customer.

As an enterprise with strong social responsibility, our company sticks to the principle of “Happy at work, Happy in life”. We want to have each employee to work with a happy and positive mind, ensuring that all of our products reach top quality standard by 100% before entering the market. Our goal in quality control is to have less than 1% complaint rate. We will consistently follow the operation concept of “Putting technology as the foundation, pursuing super water-saving technology; Putting sincerity first, and pursuing long-term and a win-win cooperation with each customer”.

We look forward to having deep cooperation with every friend and creating a prosperous future together!

Topic: Tips on How to Fix Toilet Water Tank Problem Effectively

China BQM specializes in designing and manufacturing Toilet Water Tank Fittings such as Toilet Tank Fill Valve, Toilet Tank Flush Valve, Push Button, Toilet Bowl Rubber Gasket etc.
California Car Insurance

China BQM is located at the special economic zone & seaport city of Xiamen. We specialize in designing and manufacturing toilet water tank fittings such as fill & flush valve, push button, water-saving devices, and other related products.
Website: http://www.bqmtankfitting.com

Author Bio: China BQM specializes in designing and manufacturing Toilet Water Tank Fittings such as Toilet Tank Fill Valve, Toilet Tank Flush Valve, Push Button, Toilet Bowl Rubber Gasket etc.
California Car Insurance

Category: Advice
Keywords: How to Fix Toilet Water Tank, How to Repair Toilet Water Tank, Tips to Solve Water Tank Problem