Cooling is the transfer of heat energy via radiation, conduction or convection. But how does cooling really work in air conditioning systems.

Air conditioning cooling systems take advantage of a very clever physical law. When a fluid converts to a gas, it absorbs heat and conversely, when a gas converts to fluid, it releases heat.

Air conditioning systems use these principles over and over again to move heat from one location to another (e.g. from indoors to outdoors). In very simple terms, they use a closed loop of pipes to circulate a compound. Within this system is a compressor to convert the compound to a gas (therefore absorbing heat) and an expansion valve to convert it back to fluid (releasing heat). It’s a little more complicated than that, but if you keep that simple concept in mind when reading the rest of this article.

Before we move on, just to let you know the compounds cooling systems use are known as refrigerants which have special qualities that allow them to change from fluid to gas (and vice versa) at much lower temperatures, thus better facilitating the cooling process. So here goes in a bit more detail:

1. When hot inside air flows over the cold, low-pressure inside evaporator coil (more commonly known as the inside air handling unit), the refrigerant inside absorbs heat and as it does so, it changes from a fluid to a gas.

2. To keep cooling efficiently, the air conditioner has to convert the refrigerant gas back to a fluid again. To do that, a compressor puts the gas under high pressure, a process that creates unwanted heat.

3. All the extra heat created by compressing the gas is then evacuated to the outdoors with the help of a second set of coils called condenser coils, and a second fan. As the gas cools, it changes back to a fluid.

4. The fluid refrigerant runs through an expansion valve, and in the process it evaporates to become a very cold, low-pressure gas. This is feed back into air handling unit and the process starts all over again.

It\’s easy to see that there are two distinct things going on in an air conditioner. Refrigerant is chilling the indoor air, and the resulting gas is being continually compressed and cooled for conversion back to a fluid again.

Now lets look at the various components of a cooling air conditioner in more detail:

The compressor (which is controlled by the thermostat) is at the \’heart\’ of the system. It acts as the pump, causing the refrigerant to flow through the system. Its job is to draw in a low-pressure, low-temperature, refrigerant in a gaseous state and by compressing this gas, raise the pressure and temperature of the refrigerant. This high-pressure, high-temperature gas then flows to the condenser coil.

The outside condenser coil is a series of piping with a fan that draws outside air across the coil. As the refrigerant passes through the condenser coil and the cooler outside air passes across the coil, the air absorbs heat from the refrigerant which causes the refrigerant to condense from a gas to a fluid state. The high-pressure, high-temperature fluid then reaches the expansion valve.

The inside evaporator coil is a series of piping connected to a furnace or air handler that blows indoor air across it, causing the coil to absorb heat from the air. The cooled air is then delivered to the house through ducting. The refrigerant then flows back to the compressor where the cycle starts over again.

The inside ‘Air handling Unit’ of an air conditioner contains the evaporator and a fan that blows air over the chilled coils and into the room. The outside part of the air conditioning unit contains the compressor, condenser and another fan to vent hot air coming off the compressed refrigerant to the outdoors.

In between the two sets of coils, there\’s an expansion valve. It regulates the amount of compressed fluid refrigerant moving into the evaporator. Once in the evaporator, the refrigerant experiences a pressure drop, expands and changes back into a gas. The compressor is actually a large electric pump that pressurizes the refrigerant gas as part of the process of turning it back into a fluid. There are some additional sensors, timers and valves, but the evaporator, compressor, condenser and expansion valve are the main components of an air conditioner.

Described above is a conventional setup for an air conditioner and it is known as a ‘split’ system.

Peter Hunter is a Director at Air Intelligence Ltd. With 25 years expereince, they are leaders in the provision of commercial air conditioning and commercial heating through London and the Home Counties. Locationed in Berksire (see Air Conditioning Berkshire for details)

Peter Hunter is a Director at http://www.airintelligence.co.uk . They are leaders in the provision of commercial air conditioning and commercial heating through London and the Home Counties.

Author Bio: Peter Hunter is a Director at Air Intelligence Ltd. With 25 years expereince, they are leaders in the provision of commercial air conditioning and commercial heating through London and the Home Counties. Locationed in Berksire (see Air Conditioning Berkshire for details)

Category: Advice
Keywords: air conditioning, hvac, commercial heating, ventilation, air conditioning, cooling, heating and cool